We look at the damage, explain what it needs and give you a written price before we start.
Filing a claim is easier with good records. We document everything and talk to your adjuster for you.
Water does not wait for business hours, and neither do we. Call any time and we will get a team moving.
You do not have to work out how bad it is on your own. Call, tell us what you see, and a Fullerton technician will explain the next step and what it should cost.
There are two ways an attic ends up wet. From above, rain enters through failed flashing, worn shingles, or the seals at chimneys and vents. The house itself sends moisture upward too, and in a poorly ventilated attic it condenses on cold sheathing. Whichever it is, few people ever go up and look. Our team in Fullerton inspects the attic, finds the source, and dries it out.
Wet insulation is the heart of most attic jobs. Heating and cooling bills go up because cellulose and fiberglass alike give up R-value when wet. Worse, soaked insulation holds water against the ceiling drywall and the framing for weeks. Our process is to pull the saturated insulation, dry the wood using dehumidifiers and air movers, and treat mold found on rafters or sheathing.
Our inspection covers the flashing points, roof deck, exhaust ducts and vents, and tells us if the water is condensation, a leak, or both. How far it spread is shown by moisture meters and thermal imaging.
We bag and remove insulation that is moldy or saturated, which lets the drywall and wood beneath it dry. Rooms under the attic are protected, and the route in and out stays contained.
Rafters, sheathing and joists are dried by air movers and dehumidifiers until their moisture levels are normal. We clean visible mold off the wood, then apply an antimicrobial.
The roof or ventilation issue behind it is pointed out to you, and we are glad to pass what we found to your roofer. When the attic has stayed dry, the R-value is restored with new insulation.
The insulation catches and absorbs whatever rain gets by the roofing. Because the rooms below show nothing, the leak is missed and no roof repair happens.
Mold does very well on wet paper facing and damp lumber when the attic is warm and the air is still. It can start on the back side of the ceiling drywall and on the sheathing.
After repeated wetting, the insulation is saturated and water reaches the ceiling. Brown rings appear in the room below, and the drywall may start to sag.
Sheathing delaminates and loses its hold on the roofing nails. Mold spreads across large sections of the roof deck, and the rafters remain damp enough to decay.
We save what can be dried properly and remove only what cannot. Moisture readings make that call, not guesswork.
Call (810) 440-6679| Material | Can usually be saved when | Has to be replaced when |
|---|---|---|
| Cellulose insulation | Still loose, with dampness limited to the surface | In most cases, because it has packed down or soaked through |
| Fiberglass insulation | Quick drying of a small area that took clean rainwater | Wet longer than a few days, or dirty, moldy or matted |
| Recessed lights and wiring | No corrosion or moisture found during an electrician's inspection | Rust on the connections, or water inside the housing |
| Roof sheathing | Stained but solid, and it dries back to normal moisture readings | Layers coming apart, soft spots, or a sag between the rafters |
| Ceiling drywall | Flat and dry, with a stain that sealing and repainting will cover | It spent weeks under soaked insulation, or it sags or crumbles |
Some bathroom fans exhaust into the attic and never reach the outdoors, adding warm, damp air daily. That moisture condenses on the cold sheathing and looks just like a roof leak.
The underside of the roof deck is a common place for mold when ventilation is poor. Before anyone looks, it may already have spread over a large section.
Cable runs, junction boxes and recessed light housings are all found in attics. When they get wet there is a risk of shock and fire, so keep out until the power has been checked.
Many attics hold an air handler, a drain pan and condensate lines. For weeks an overflowing pan or blocked drain can drip into insulation, and there is no storm to tip you off.
Have a different question? Call us and we will answer it over the phone.
Call (810) 440-6679Don't wait for small problems to become expensive emergencies. Call Fullerton Restoration for fast, reliable service.
Call (810) 440-6679 Now